OPT-DPA6024-2 High Power Current Digital Controller
Catalog Dowload Demo & SDK |
Model No. | |
Product Features 1. 256 intensity levels 2. Short circuit protection 3. Trigger signal input: connect an external signal source (e.g. a camera trigger signal) for synchronized strobing of the illumination device 4. Configuration via PC: The intensity and triggering of the light can be controlled via RS232 interface. We offer corresponding software to help you integrate the illumination into your system. 5. Manual control of the intensity directly at the controller is available. 6. The controller setting is stored within the device, even when switched off. |
Device Overview |
NO. | Item | Description |
1 | Company logo | OPT brand |
2 | Power switch key | To turn the controller on/off |
3 | Digital screen | The first number indicates the channel and the other 2 numbers show intensity value |
4 | Pilot lamp | Shows the status of the channel, ON means active, OFF means inactive. |
5 | Operating key | S: Set/check button, +: plus, -: minus |
6 | Light connector | For the connection with OPT line lights |
7 | Trigger connector | For connection with an external trigger source such as a PLC, sensor or camera |
8 | AC power input | 100 - 120 V AC or 200 - 240 V AC |
9 | PE: Ground | Ground protection |
10 | Fan | For cooling |
11 | Serial port, female | For the connection with PC |
Step 1: Refer to drawing above to connect the light with the controller. Step 2: For external triggering, connect the external trigger source with the trigger port Step 3: Connect the controller with a 100 -120V AC or 200 - 240V AC power source and switch the controller on. The digital display is lit. If the intensity of the light shall be controlled via PC, you need to connect the PC with an RS232 cable or Ethernet cable before the controller is switched on. Use the provided software or your own application to communicate with the controller. You can adjust the settings via the PC or manually. |
Connector specification |
Pin | Pin Definition | |
1 | Light+ | |
2 | Light- | |
3 | Fan+ | |
4 | Fan- | |
5 | Res | |
6 | Res |
Parameter Description |
Item | Parameter | Instruction |
Rated power | 5A, 24V | For 24V line Light |
Intensity control | 256 levels | Adjust by the intensity adjust key or DEMO software |
Trigger mode | Switch trigger | Supports NPN output |
External trigger input | Synchronous strobe with external signal | |
Short cricuit protection | Yes | Be started when output is short circuit |
Trigger delay time | ≤100μs | |
External trigger frequency | 1KHz Max. | |
Channel | 2 | |
RS232 communication Baud Rate | 9600BPS | For parameter setting and control of the device |
Output power | 144W per channel, 288W per 2 channels | Total output power of 2 channels < 300 W |
Input voltage | Input 100-120V AC or 200〜240V AC | Can be changed by internal switch |
Hi-Pot test | 1500V AC, 1 min Max. | Leak current < 1mA |
Insulation resistance | 500V DC | >20 MΩ |
Standby power consumption | <11W | |
Size (mm) | 136 x 326 x 104.5 | |
Weight(kg) | 2.1 |
Trigger Port DPA6024- 2 has two trigger channels, each channel has a “+” and “-“ pin. See the wiring diagram below for details. Trigger Mode Setup This digital controller has two modes, “ON” and “OFF”. See the table below for details. |
Output mode | Description |
ON | Trig+ and Trig- are off : the light is ON. Trig + and Trig- are short circuit: the light is OFF |
OFF | Trig+ and Trig- are off : the light is OFF. Trig+ and Trig- are short circuit: the light is ON |
Sequence Diagram ◆ ON mode When connect with external signal, Trig+ and Trig- are off (high voltage level), the Light is ON; To do short circuit to Trig+ and Trig- (low voltage level), the Light is OFF. ◆ OFF mode When connect with an external signal, Trig+ and Trig- are off (high voltage level), the Light is OFF; To do short circuit to Trig+ and Trig- (low voltage level), the Light is ON. |
Remark: 0 - 1 V is low voltage level, 5 - 24 V is high voltage level. |
Wiring Scheme of Switch and Trigger Port |
Dimensions [mm] |